Shrinkage of textile fabric and its influencing factors

Aug 22, 2021

Leave a message

Textile shrinkage


"The shrinkage rate of synthetic fibers and mixed textiles is the smallest, followed by wool, linen and cotton fabrics in the middle, silk fabrics shrink more, and viscose fiber, rayon, artificial wool fabrics are the largest."


Objectively speaking, the cotton fabric has the problem of shrinking and fading, the key is the finishing behind. So the fabric of general home textile is processed through pre-shrinkage. It is worth noting that after pre-shrinkage treatment is not equal to no shrinkage, but refers to the shrinkage rate control in the national standard 3%~4% to, underwear material, especially natural fiber material will shrink.


Therefore, in the choose and buy cloth, in addition to the quality of the fabric, color, pattern to choose, the shrinkage rate of the fabric should also be understood.


Shrinkage of general fabric




Cotton: 4% ~ 10%;




Chemical fiber: 4%~8%;


Cotton polyester: 3.5%~ 5%;


Color white cloth: 3%;


Poplin: 3~4.5%;


Twill: 4%;


Denim: 10%;


Artificial cotton: 10%.


Effect of fiber and shrinkage


As the fibers themselves absorb water, they swell to a certain extent. The swelling of fibers is usually anisotropic (except for nylon), that is, the length is shortened and the diameter is increased. The percentage difference between the length of a fabric and its original length is usually called shrinkage. The stronger the water absorption capacity, the more intense the swelling, the higher the shrinkage rate, the worse the dimensional stability of the fabric.



The length of the fabric itself is different from the length of the yarn (silk) used, and the difference is usually expressed by the rate of shrinkage. Weaving shrinkage (%) = [yarn (silk) length - fabric length] / fabric length


Fabric in water, due to the swelling of the fiber itself, the length of the fabric is further shortened, resulting in shrinkage. The shrinkage of a fabric varies according to its shrinkage. The shrinkage rate of the fabric is different with the difference of fabric structure and weaving tension. The weaving tension is small, the fabric is dense and thick, the weaving shrinkage is large, the shrinkage of the fabric is small.


The weaving tension is large, the fabric is loose and light, the weaving shrinkage rate is small, and the shrinkage rate of the fabric is large. In the dyeing and finishing process, in order to reduce the shrinkage rate of the fabric, the pre-shrinkage finish is often used to increase the weft density and improve the shrinkage rate in advance, so as to reduce the shrinkage rate of the fabric.


Causes of shrinkage


Fiber in spinning, or yarn in weaving and dyeing and finishing, the fabric of the yarn fiber elongation by external force or deformation, stress in fiber yarn and fabric structure at the same time, in the static dry relaxation state, or static wet relaxation condition, or in a dynamic wet relaxation condition, total relaxation condition, different degree of internal stress release, make the yarn fiber and fabric back to the initial state.


2. Different fibers and fabrics, the shrinkage degree is different, mainly depends on the characteristics of the fiber - hydrophilic fiber shrinkage degree, such as cotton, linen, viscose and other fibers; And hydrophobic fiber shrinkage degree is less, such as synthetic fiber.


3. In the wetting state, the fiber will swell under the action of the immersion, which will increase the diameter of the fiber. In the case of the fabric, the radius of curvature of the fiber at the interleaved point will be increased and the length of the fabric will be shortened. For example, cotton fiber expands under the action of water, the cross-sectional area increases 40~50%, the length increases 1~2%, and synthetic fiber is on the heat contraction, such as boiling water contraction, generally about 5%.


4. When the textile fiber is heated, the shape and size of the fiber change and shrink, and can not return to the initial state after cooling, which is called the thermal contraction of the fiber. And the percentage of the length before and after thermal shrinkage is called thermal shrinkage, generally in boiling water shrinkage test, in 100℃ boiling water, the percentage of fiber length shrinkage is expressed.


It is also useful to measure the percentage of shrinkage in hot air at more than 100℃, and it is also useful to measure the percentage of shrinkage in steam at more than 100℃. The performance of fiber is also different under different conditions such as internal structure and heating temperature and time. For example, the boiling water shrinkage rate of polyester staple fiber is 1%, the boiling water shrinkage rate of pVA is 5%, and the hot air shrinkage rate of CHLORINE fiber is 50%. There is a close relationship between the fiber processing and the dimensional stability of the fabric, which provides some basis for the design of the subsequent process.



Causes of shrinkage


1. Raw materials


Fabric of different raw materials, shrinkage rate is different. Generally speaking, the hygroscopicity of large fiber, fiber expansion after soaking in water, diameter increase, length shorten, shrinkage rate is large. If some viscose fiber water absorption rate is as high as 13%, and synthetic fiber fabric moisture absorption is poor, its shrinkage rate is small.


2, density,


The shrinkage rate varies with the density of the fabric. If the density of longitude and latitude is similar, the shrinkage rate of longitude and latitude is also similar. If the fabric is dense, the warp shrinkage will be greater; conversely, if the weft density is greater than the warp density, the warp shrinkage will be greater.



3, yarn count thickness



The shrinkage rate of the fabric varies with the yarn count. The shrinkage rate of cloth with coarse count is greater, and that of fabric with fine count is less.



4. Production process


Fabric production process is different, shrinkage rate is also different. Generally speaking, the fabric in the process of weaving and dyeing and finishing, the fiber should be stretched many times, the processing time is long, and the shrinkage rate of the fabric with greater tension is large, and the other way around is small.



5. Fiber composition


Natural plant fibers (such as cotton, hemp) and plant regenerated fibers (such as viscose) and synthetic fibers (such as polyester, acrylic) are easy to hygroscopic expansion, so the shrinkage rate is larger, and wool is easy to felt because of the scale structure of the fiber surface, affecting its dimensional stability.



6. Fabric structure


In general, the dimensional stability of woven fabric is better than knitted fabric. The dimensional stability of high density fabrics is better than that of low density fabrics. In woven fabrics, the shrinkage rate of plain weave fabric is less than that of flannel fabric. In knitted fabrics, the shrinkage of plain needle is smaller than that of ribbed fabric.



7. Production and processing process



As the fabric is unavoidably stretched by the machine during dyeing, printing and finishing, tension exists on the fabric. However, the fabric is easy to release tension after being exposed to water, so we will find that the fabric shrinks after washing. In practice, we usually use pre-shrinking to solve this problem.



8, washing care process


Washing care involves washing, drying, and ironing, each of which affects the shrinkage of the fabric. For example, the dimensional stability of hand-washed samples is better than that of machine washed samples, and the washing temperature also affects its dimensional stability. In general, the higher the temperature, the worse the stability. The drying method of the sample also has a great influence on the shrinkage of the fabric.



The commonly used drying methods are drip drying method, metal mesh tile method, hanging dry drying method and rotary drying method. The effect of drip-drying method on fabric size is the least, and the effect of rotary arch drying method on fabric size is the largest, and the other two kinds are in the middle.



In addition, according to the composition of the fabric to choose a suitable ironing temperature, can also improve the shrinkage of the fabric. For example, cotton and linen fabrics can be ironed at high temperatures to improve their shrinkage. But it is not the higher the temperature, the better, for synthetic fiber, high temperature ironing not only can not improve its shrinkage, but will destroy its performance, such as fabric hard brittle.



source:https://mp.weixin.qq.com/s?__biz=MzI2NDA4NDUzNw==&mid=2650927919&idx=1&sn=d3d40762f11f7dde642b235fb13f51d1&chksm=f1475e79c630d76f1537bb55b34aca94af2e96cf37402844d34808e74a5ab1ad7bf96fddf7e4&mpshare=1&scene=1&srcid=0930lpvrmP8nFBecotWuYx9Q&sharer_sharetime=1629358205378&sharer_shareid=ff5f2139d31a4580928c819c5eb948df&exportkey=AVDCBAFhbZMwjludxsSch3g%3D&pass_ticket=RLqGpecqR%2Fv6Q4VqK7kvMOJ86imSe7wZzMvmM%2F%2FmOXiyA8CAlwCeCMac9NgcR9xP&wx_header=0#rd