1、 Foreign fiber control process flow
Package selection (removing raw materials with more foreign fibers) → package preparation (leaving room for picking foreign fibers) → package brushing (brushing off oil stains and various foreign fibers remaining on the package surface) → package arrangement (picking out foreign fibers in the package table) → foreign fiber machine (properly adjusting and using foreign fiber machine) → check defects in each process (picking out foreign fibers in the product) → electrical cleaning (reasonably setting up self winding foreign fiber removal function) → cloth surface test verification (according to the verification results, make full use of PDCA cycle inspection to improve the heterofiber control process).
2、 PDCA cycle control procedure for different fibers
2.1 package selection
According to the requirements of the contract and order (bleaching, dyeing, etc.), raw cotton shall be selected and selected before the raw materials enter the workshop. The general practice is to pull a small number of cotton bales for manual unpacking and inspection in advance according to the situation of raw cotton in stock, select according to the number of foreign fibers inspected, and focus on the raw materials with more foreign fibers, so as to lay a good foundation for the control of foreign fibers in the next process.
2.2 spare package
It is necessary to consider the next step of the brushing work and reserve a good working space for the brushing workers. Generally, a gap of 30-50cm is reserved between the bags to facilitate the brushing workers to find the three filaments, color lines, red and blue dots and other foreign fibers on the surface of the raw cotton bags.
2.3 bag brushing
Before the raw cotton enters the bale table, the surface of the bale shall be cleaned of dirty cotton, oil stain and various residual foreign fibers. The scaffolder shall carefully brush the package with a hand lamp from top to bottom, and shall be equipped with special storage equipment for brush package flowers. The cotton package shall be separately collected, stored and picked. The cotton package after brushing shall be clearly marked to prevent missing or repeated brushing.
2.4 packing
During packing, it is necessary to prevent the broken plastic of the packing belt from splashing into the raw materials, formulate the packing method, configure special tools for unpacking, and set up a packing desk for special personnel to pick up and check.
2.5 use and management of foreign fiber machine
2.5.1 installation position of foreign fiber machine
In the blowing process, it is necessary to reasonably determine the installation position of the foreign fiber machine. In general, it can be installed after the cotton opener to make the cotton lump smaller after the raw cotton is picked, mixed and opened, so as to improve the effect of foreign fiber detection and elimination.
2.5.2 reasonable adjustment of foreign fiber machine
(1) The flow rate setting of cotton flow must be consistent with the actual flow rate, and the lag time is calculated according to the flow rate to ensure the accurate discharge of the detected foreign fibers.
(2) After the flow rate is set, turn on the corresponding detection module. The white foreign fiber module is set by 0 # and 1 # cameras, and the anti fluorescent foreign fiber is set by 2 # cameras. After the setting is completed, the cotton passing teaching must be done. The cotton must be fed continuously during the teaching. After the teaching is completed, the parameters can be adjusted according to the foreign fiber ejection.
2.5.3 method for regular inspection of foreign fiber machine
During the use of the foreign fiber machine, the test paper shall be tested once a week, and 1 × Test 10 pieces of 4cm red, blue and white test papers respectively, and it is qualified if the picking rate reaches more than 90%.
2.5.4 maintenance of foreign fiber machine
In order to ensure the normal state of the foreign fiber machine, we have formulated the maintenance methods of the foreign fiber machine, wiping the glass and the mirror with clean non-woven cloth every day; Clean the dust in the filter screen and the computer host once a week, and clean the dust in the light box once a month; Regularly drain the moisture in the air tank and filter the pressure regulator.
2.5.5 operation management of foreign fiber machine
The patrol inspection, data recording and analysis of the foreign fiber machine shall be standardized, and the discharge times of the foreign fiber machine shall be recorded every hour. If there is any abnormality, it shall be determined whether there is a foreign fiber package according to the picking situation of the sorter; Check the discharge curve from time to time to determine whether there are lamp hanging, non lighting and channel hanging; During the shift handover, each shift shall do a good job in the operation status handover and data comparison of the foreign fiber machine, and accurately grasp the changes of the foreign fiber discharge data, as shown in Fig. 1.

Fig. 1 operation chart of jwf0016c foreign fiber machine
2.6 arrangement of pickers
A fixed picker is arranged at the head of the cotton drum and the flower wrapping table to pick up foreign fibers at any time during the production process. The tasks of the picker are mainly three:
(1) Pick large pieces of cloth and other foreign fibers to avoid crushing after being hit.
(2) Timely confirm and exchange cotton bales with excessive foreign fibers.
(3) The main types of foreign fibers in raw cotton are determined by classifying the foreign fibers picked out by the picker, and fed back to the adjustment personnel of the foreign fiber machine, so as to reasonably adjust and set the sensitivity of the foreign fiber machine and improve the removal efficiency of the foreign fiber machine
2.7 reward system for each process
Establishing a quality control system for the product quality of the next process to the previous process can not only prevent foreign fibers, but also reduce yarn defects, stabilize quality and improve production efficiency. Employees will be rewarded with 10 points for each defective yarn and strip. Meanwhile, the cleaning and sorting workers and the person in charge of foreign fiber machine maintenance will be assessed to stimulate the enthusiasm of employees for quality control.
2.8 application of electric fiber cleaning function
According to the different spinning varieties and fabric quality requirements (yarns for bleaching or dyeing), reasonably set the function of electric fiber cleaning, focus on optimizing and adjusting the setting of electric fiber cleaning extreme value and auxiliary points, open the defect stuck mode for defect verification, conduct small batch spinning test first, and then spin large goods after the fabric is verified to be qualified. Check the trend chart of foreign fiber shearing and the number of shear defects every day to ensure that the trend of foreign fiber yarn cleaning curve is stable. Once the foreign fiber cleaning curve fluctuates, it is necessary to find out the type of foreign fiber that fluctuates in time, analyze the jamming according to the classification of foreign fiber, strengthen the control of the previous process according to the analysis results, and track and verify the foreign fiber situation on the cloth surface in the weaving factory to verify the effect of electrical cleaning adjustment. The setting of our company's foreign fiber parameters is shown in Fig. 2 for ordinary bleached cloth yarn and Fig. 3 for semi Matt bleached cloth yarn.

Fig. 2 setting of foreign fiber yarn cleaning for ordinary bleached cloth

Fig. 3 setting of yarn cleaning for semi Matt bleached cloth
2.9 control procedure for order foreign fiber
After receiving the customer's order, our company should first review the customer's requirements for different fibers, determine the trial spinning sample after cotton blending, and then go to the cloth factory to test weave the cloth surface, verify the control effect of different fibers, and then put into mass production after passing the verification. After large-scale goods are put on the machine, we will also go to the weaving factory to try to weave small samples in time, and submit them to the finishing workshop, quality inspection and other departments of the weaving factory for verification. According to the type of foreign fibers on the fabric surface, we will feed back to the spinning factory to find out the causes, adjust the type of spray picking of the foreign fiber machine and the key points of brushing and picking, and achieve closed-loop control of foreign fiber management.
After the implementation of the foreign fiber control procedure, the foreign fiber of the fabric surface of our company's products has been effectively controlled. The varieties with strict requirements for foreign fiber such as bleaching and semi extinction can also meet the requirements of customers. The foreign fiber is controlled within 10 points, which is highly praised by customers.
3、 Conclusion
It is difficult to ensure the stability and consistency of the effect by relying solely on the foreign fiber control of the foreign fiber machine. Therefore, we have made the foreign fiber control process, combined manual picking with the control of the foreign fiber machine, checked and fed back each process step by step, and constantly revised and improved the control means according to the feedback information, forming a closed-loop management of foreign fiber control from raw cotton to cloth. We have achieved obvious results, and customer feedback has greatly decreased
source:https://mp.weixin.qq.com/s/5xIw9njsZX_CjeETXpWxPg
