1、 History of semi-worsted technology
The "semi worsted" technology appears occasionally. Usually the length of wool fiber is in the range of 70~110mm. In the last century, New Zealand produced a kind of wool with a length of about 50mm, and tried a new spinning process: wool blending → carding → sliver carding → carding → roving → spinning. This process is different from the traditional long worsted process. The carding machine directly enters the spinning process without combing and repeated carding after sliver formation. People call this process semi-worsted. Since 50mm is equivalent to the length of medium and long fibers in cotton spinning, it meets the requirements of cotton spinning technology and is gradually popularized and applied by cotton spinning enterprises.
2、 Blending of wool and cotton spinning technology
Although the number of spindles of wool spinning is only a few million, wool spinning, especially worsted spinning, is specialized in producing high-grade products with high added value, which are exported to developed countries in Europe, the United States and Japan in exchange for a huge amount of foreign exchange. Some new spinning technologies of wool spinning have a deep impact on the development of cotton spinning technology, such as the application of siro spinning, sirofil spinning, cable spinning and so on. Cotton spinning has more technical means to cope with various fibers with poor spinnability, such as the production of high-count lightweight fabrics, various elastic fabrics, low-twist and even non-twist fabrics, and has greatly enriched the existing non-cotton products, which have far exceeded the category of wool and cotton spinning products.
Today's scientific and technological progress is dizzying, and inter-bank and cross-border technologies penetrate, blend and inspire each other. Cotton spinning has made full use of the above technologies. In the market, the so-called AB yarn, hemp grey yarn, core-spun yarn, non-twist yarn and ultra-fine yarn spinning (cotton fiber wrapped on the backbone of soluble filament), embedded spinning and other technologies widely use the technical principles of Siro spinning and Sirofil spinning, which is convenient for transformation. With the structure of siro ply yarn, the hairiness is greatly reduced, and the quality and cost of cotton spinning benefit greatly. As far as hairiness is concerned, the special way of sirofil spinning is "pre twist" and then "strong twist", which reduces the hairiness production at the initial stage. The cable-spun yarn has less hairiness, high strength and good wear resistance. It can significantly improve the output and efficiency of spinning, self-winding and weaving machines. At the same time, it saves the twisting process and shortens the spinning process.
Many of the raw materials used in semi-worsted spinning are dyed yarn, and the grade of raw materials used is high. It organically combines modern cotton spinning technology with wool spinning technology to produce semi-worsted yarn with different styles. The yarn has both the characteristics of fine wool spinning and the style of coarse wool spinning, which makes up for the weak links such as low yarn count, excessive hairiness and uneven evenness produced by the coarse wool spinning process. At present, a large number of yarns have been produced on flat knitting machines, large round knitting machines of weft knitting machines and rapier, air jet, projectile shuttle and other looms of shuttleless looms. Because semi-precision spinning generally uses high-grade fiber raw materials such as wool (thread), cashmere, hemp fiber, spun silk, etc., the grade of semi-precision color spinning is higher than that of cotton and other types of color spinning, enabling enterprises to obtain higher profit space.
3、 Bottleneck of cotton semi-worsted technology
At present, the pre-spinning equipment of the cotton mill itself is limited, and it is designed for processing cotton fiber with relatively simple functions. Some enterprises that transform non-cotton production mode and produce with the help of semi-worsted technology cannot adapt to the production form of "small batch, multi-blend and multi-variety", which makes the traditional cotton spinning process difficult to cope with, and the quality and production cannot be guaranteed, resulting in the following problems:
First, in order to deal with small orders, the pretreatment equipment is temporarily patched up, which is not systematic and formal, and is not conducive to quality, and the requirements of loosening, mixing, penetration, and unevenness are also required.
Second, the overall performance of each incoming raw material is not controlled. Due to the lack of special instruments, the physical and chemical performance parameters, specific resistance, spinnability and other relevant indicators of the fiber are often too frequently changed to detect the fiber, or simply do not do so. Some good textile enterprises do single mark or blended fast trial spinning to test spinnability, but not systematically.
Third, the source, model and proportion of antistatic agent, crude oil and antiskid agent used in raw material curing or pretreatment are not optimized, and the use is not standardized. Many so-called experiences are just inefficient, low-speed, not universal, and without standard technical support.
Fourth, under the production mode of multi-variety and multi-mixing, it is difficult to balance the contradiction between small batch and mixing uniformity and quality, especially color spinning. In order to ensure the mixing quality, many textile enterprises still use the process of manual cotton mixing, raw material → pre-opening → raw material weighing → manual cotton mixing → packaging. That is, manual pre-opening (tearing), weighing (weighing according to the proportion of the feeding sheet), and cotton mixing (evenly distributed up and down) are labor-intensive.
The process of cotton cleaning, mixing and drawing can not be completed at one time; Disc mixing has great damage to the fiber and is easy to produce bunches and neps; The traditional cotton blending machine "lay horizontally and take directly" belongs to the "time difference equal thickness" cotton blending, and the mixing is not accurate; Multiple warehouses can realize "equal ratio and unequal thickness"; Adding two four bins in the cotton cleaning process can solve the problem of uneven mixing, but it cannot be mixed uniformly in small batches and multi-components.
Secondly, in view of the particularity of wool, hemp and silk in non-cotton raw materials, that is, most of them are short fibers or noils of different lengths in the process of carding or processing, and even the next step. Because of the difference in the original processing technology, additives, and crude oil, the surface properties and friction factors of raw materials are different. Once entering the traditional cotton spinning and clearing process, What type of beater (angle nail, cylinder, nose shape, sawtooth, etc.) and dust rod (triangle, rectangle or circle) or bottom leakage (seal or open) are used, at what speed, the basic configuration of uniform mixing, whether the fiber is damaged, whether there will be winding and unable to roll. There is no matching system to classify the normal carding and production of wool, hemp, silk and other fibers according to the blending ratio of the flat card and related card clothing equipment. At the same time, production is based on efficiency, smoothness, stability and intelligence. Only in this way can we control the technology and solve the technical weaknesses.
4、 Success in raw material determination
The semi-worsted raw materials come from a wide range of natural fibers such as wool, hemp and spun silk in non-cotton fibers, polyester, acrylic, nylon, polypropylene and vinylon in chemical fibers, ultra-fine denier, high-strength and high-modulus chemical fibers (carbon fiber and aramid) in functional fibers, and Tencel, Modal and Lyocell in cellulose fibers.
The performance of raw materials depends on whether the production is stable and smooth in the whole process, and whether the normal production can be achieved by simple pretreatment instead of problems such as entanglement, winding and blocking. The number of lint and broken ends increases, the production cannot be continuous, and the production rate is obviously low, which seriously affects the production cost and efficiency. Therefore, the development of products by enterprises is closely related to the market demand and the purchase of appropriate raw materials.
The diversity of raw materials has also brought a variety of raw material channels, such as large chemical fiber, small chemical fiber, small workshop processing fiber, recycled fiber, etc., which have affected the production and quality of textile enterprises. The raw materials of wool, hemp and spun silk are rich and colorful:
Wool usually refers to cotton wool, including fine wool, semi-fine wool and ultra-fine wool. According to the processing methods, it includes: drawn and cut wool, carbonized wool, short wool, loose wool, cut wool, and according to the processing methods, it includes drawn wool, expanded wool, mercerized wool, shrink-proof wool, and anti-pilling wool. Special wool includes mohair, rabbit hair, yak hair, camel hair, alpaca hair, mink hair, etc., rare cashmere, yak hair, camel hair, lamb hair, colored hair, etc., as well as imported Australian hair, New Zealand hair, Argentine hair, etc.
The hemp raw materials can be purchased from professional hemp processing factories. There are mainly flax and hemp raw materials factories in the north, and there are ramie, hemp and sisal raw materials factories in the south, providing hemp raw materials for primary processing with different spinning requirements. There are five kinds of ramie: fine and dry ramie, fine and dry ramie (short ramie), noil (old technology), noil (new technology) and sliver. There are also five kinds of flax: beaten flax, coarse flax, machine short flax first combed, combed short fiber, short flax combed and noil of combined carding machine. The second coarse flax processed by hand wheel flax making machine can be processed into cotton flax (commonly known as flax cotton) with an average fiber length of 30~40mm and impurity content of less than 3%, which can be used in cotton spinning industry to make flax/cotton blended yarn. There are also four kinds of hemp fiber used for color spinning: cotton fiber, cashmere fiber, combed noil, and combed hemp sliver.
The spun silk processes the defective cocoons and waste silk produced in sericulture, silk making and silk weaving, and obtains the final drop cotton as the silk spinning raw material after the round carding machine or direct carding drop cotton and cutting cotton. It is a staple fiber and is also the silk raw material commonly used by cotton mills. Among them, the price of mulberry cocoon silk is relatively expensive, while the price of tussah cocoon silk, wild silkworm cocoon silk and castor cocoon silk is relatively affordable.
The purchase of non-cotton raw materials is more detailed than the classification of cotton. The same raw material affects the price according to the fiber length, uniformity, processing depth, spinnability, and final product style. It involves the production cost, production rate, efficiency, etc. It needs to be carefully calculated to find the production and operation balance of its own enterprise.
5、 Solve technical problems in cotton spinning processing
How to get through this link, we need to work together and consider it systematically and comprehensively. At the same time, to solve the problem of information fragmentation, the author is only throwing a brick to attract jade.
First, the cotton spinning factory absorbs the advantages of the equipment and technology of wool, linen and silk spinning enterprises to solve the technical bottleneck of producing some fibers with poor spinnability in the previous stage. Because the country has already finalized a batch of advanced equipment for wool spinning, silk spinning and other equipment, the blending carding has its unique features. The textile machinery factory integrates the essence of cotton spinning and wool spinning equipment, and re innovates the wool spinning multi link cotton carding machine, wool blending machine, carding machine, including thugs, clothing equipment and other new technologies developed with cotton spinning, grafting intelligent, information technology to accurately control the mixing ratio of different fibers, so as to achieve continuous, automatic, high-yield Simple and flexible blowing-carding line.
At present, in addition to borrowing the blending technology of "wool blending machine → fan → wool blending bin", the old carding machines A186D, F, G, FA201 series, etc. have been reformed to achieve the type of one machine and one bucket, that is, the general semi-worsted volumetric shock feeding bucket. High-end fine wool machine (cashmere blending) has a uniform wool hopper to meet the needs of product upgrading and high quality.
In order to reduce costs and purchase materials with poor length and entanglement, we can refer to the equipment such as worsted opening machine, cutting machine, carding part comber, comb machine and so on, which can adapt to the flexible variety renovation and process adjustment. The currently developed semi-worsted carding machine is the sizing equipment that combines wool feeding, weighing, opening and cotton carding to suit the semi-worsted raw materials; Promote simple blowing-carding unit, and the pipeline connecting blowing-carding and carding can be flexibly adjusted according to the batch of mixed varieties.
Second, there is room for improvement in the functionality, intelligence and convenience of cotton spinning equipment. Work hard to adapt to the adaptability of multi-variety renovation to meet the trend of personalization, small batch, multi-variety and multi-color number.
Research and develop automatic process equipment for intelligent unpacking, palletizing, counterweight grabbing and blending suitable for blending and color spinning. Modern laser ranging technology can solve the phased operation of cotton bale picking and releasing manipulator and the positioning of cotton bale picking and releasing. Visual recognition system and coding and decoding system solve the identification, tracking and management of cotton bales and fiber varieties. The sensor system solves the problem of electronic counterweight and accurate grasping.
The combination equipment that can be implemented in the multi-variety and small-batch production mode has been applied. The fine cotton mixer (such as JSB125) and the connection opener (such as JSK510) are suitable for small-batch production of wool cotton and flax cotton. When the process route of "full mixing is the main, and strip mixing is the auxiliary" is adopted, the connection of cotton grabber and opener can be used for large-batch continuous production.
The cotton spinning carding machine needs to be developed with intelligent and adjustable carding and impurity removal to meet the quality requirements of diversified raw materials. Drawing lessons from the online monitoring of color neps on the lower end of the doffer web of the foreign carding machine and the online grinding of the cylinder and the cover plate, the color neps and neps can be controlled stably for a long time.
Popularize the drawing frame with two eyes separately adjusted technology (such as TMFD81S drawing frame). There is no need to change the process gear, and the two-eye servo motor can independently and steplessly change speed, which can meet the needs of frequent adjustment, accuracy and speed of color spinning.
Color-spun sliver blending machine (also known as color drawing machine) can be used for the production of cotton and cotton-type fiber fancy spinning. With its multi-group drafting and feeding mechanism, the basic color can be used as the base color, and special process can be used to feed four-color wool sliver or cotton sliver or chemical fiber sliver with different colors. Through computer control, each group of colors can be changed alternately and proportionally, which is used for spinning color sliver with gradual color change. Its advantage is that the processing cost is lower than that of stage dyeing, And the effect of color change transition zone is obvious. The spun yarn is called rainbow yarn.
The twist change of cotton spinning frame is the same on both sides, while that of wool spinning frame, draft and twist can be changed respectively, which affects the effective use of spindle. For example, the spinning roller is driven by servo motor separately, the winding mechanism is simplified, the stepless speed regulation is realized, the process is changed, and the variety is changed.
Third, accelerate the integration of 5G+AI AI artificial intelligence, big data and cloud computing to speed up the pace of intelligence, and collect, network, test, quality forecast, efficiency analysis, energy consumption and material consumption and other information of different raw materials and different varieties of spinning processes, technologies, equipment, equipment, auxiliaries, materials, uses and cost performance. Through the integration of fragmented information, based on the CPS whole-process interconnection and intelligent visual customer interaction platform, Improve and extract more reliable, efficient and practical application technology. Let all textile enterprises achieve resource storage, intelligent optimization, decision-making, recommendation and sharing. Of course, every enterprise can start preparing for this meaningful work now.
Fourth, promote the patented blending technology of color spinning (patented technology of Guiyafu cotton blending), which is unique in China in semi-worsted spinning. This technology is also suitable for the blending effect of conventional production of multi-fiber blending in cotton mills. Its mixing concept is novel, ingenious, and simple in structure. It realizes the integration of multiple mixing principles, such as flat and straight mixing, reverse mixing, and achieves the effect of layering (stacking) mixing in proportion, and can even reduce the number of silos or cancel multiple silos. In particular, it solves the heavy manual premixing in the process of color spinning and proofing. When the cotton is fed, all kinds of raw materials should be weighed according to the mixing proportion and then directly thrown in, which improves the working environment, simplifies the operation management, and ensures the stability of color spinning mixing quality.
6、 Precautions for semi-worsted pretreatment
If the price of raw materials is expensive, it is necessary to control the lint and noil to reduce the cost. The quality of pretreatment determines the smooth production. First, control the raw materials, solve the problem of raw material spinnability selection scheme by measuring the wettability and permeability of raw oil, and then select different raw materials and different types of raw oil, and grasp the spraying method and curing time.
6.1 Pretreatment determines the key to smooth production
6.1.1 Basis of pretreatment and curing of non-cotton raw materials
From the perspective of non-cotton spinnability, pretreatment includes raw material degreasing (wool), degumming (hemp, silk), and curing (for fiber penetration and wool oil, antistatic additives, anti-skid agents, water, etc.). For cotton spinning, curing is the main method, and the specific solution is usually determined according to the specific resistance of the fiber.
① The specific resistance is less than 108 Ω g/cm2, and the pretreatment of chemical fiber and blended raw materials is relatively simple. Generally, it can be cured with water after loosening, and the proportion is determined according to the moisture regain of the fiber and the temperature and humidity of the workshop, and the curing time is 24 hours (film cover). No other oil agent needs to be added.
② Specific resistance > 109 Ω g/cm2, such as wool, hemp, silk, nylon and other fiber pretreatment requirements are relatively high, solve the problem of electrostatic winding, and achieve the moisture regain required by the process.
The selection of wool for health care and the proportion of wool oil, depending on the performance of wool oil and the characteristics of raw materials, can be appropriately reduced, usually 0.5~1.5% for imported wool and 1.0~2.5% for domestic wool. The proportion of special wool fiber (such as rabbit hair) and wool oil is generally controlled at about 2.5%, and a small amount of silica gel is added to the blended wool. Or select HA-1 rabbit hair and hair oil.
Special flax humidifier or blended crude oil can be used for hemp curing, such as 1% M80 emulsified oil, 3% No. 7 machine oil and 96% water, which are placed in the warehouse for humidification and maintenance for 24h.
For the maintenance of spun silk to reduce static electricity, the commonly used auxiliary oil agents include sandrin, antistatic agent, synthetic wool oil, glycerin, etc. A certain enterprise added 2% crude oil, 1.6% antistatic agent, and the moisture regain was controlled at 18-20% [1].
Chemical fibers with high specific resistance, such as nylon and aramid, only need to add a certain amount of antistatic agent and water. Nylon specific resistance 6.48 × 109/Ω· cm, CT-F-6 antistatic agent is selected, the antistatic agent is mixed with water in a ratio of 1:10 to make lotion, and then evenly sprayed on the loosened fiber in proportion according to the fiber weight, and cured for 24h (covered with film).
6.1.2 Type and selection of crude oil
Hemao oil is generally made of mineral oil, vegetable oil, emulsifier, softener, cluster agent, antistatic agent and other components through emulsification and mixing. Common basic raw materials include spindle oil, castor oil, archaic oil, emulsifier EM series, organosilicon, surfactant SG series, various anionic and cationic and non-ionic antistatic agent series, etc. The output of mineral oil is large, such as spindle oil, machine oil, white oil, etc., which is cheap and can be prepared by textile enterprises themselves. Water soluble and crude oil with good permeability and cohesion, and non-emulsifiable and crude oil gradually become the mainstream and crude oil; At the same time, separate lubricating oils cannot be used, and they need to be emulsified. The commonly used emulsifiers include detergent, soap, pancreatic bleach T, Pingpingjia O, Remiband, open powder, emulsifier MOA, emulsifier EL, etc; Commonly used antistatic agents are: non-ionic LD-9400H surfactant, anionic NP surfactant and cationic SN quaternary ammonium salt surfactant (synthetic fiber spinning) [2].
6.1.3 Spraying equipment mode
Spraying equipment can also be selected according to specific resistance or spinnability.
① The specific resistance is less than 108 Ω g/cm2, and there are two common ways: one is to add nozzle spray mode at the back of A035 cotton mixer, and humidification or refueling will be synchronized with the horizontal curtain movement. The second is to configure a row of nozzles and an air compressor on the beam of the cotton grabber. During the reciprocating operation of the cotton grabber, the hollow compressor will evenly spray the crude oil on the raw material.
② The specific resistance is more than 109 Ω g/cm2, and the requirements for pretreatment of wool, hemp, silk and other fibers are relatively high. Generally, there are two treatment methods.
Wool fibers are fully mixed and infiltrated by wool bin and wool machine. Sheep wool has good elasticity, poor hemp fiber cohesion, and it is not easy to clear and roll. The loose wool is generally filled with wet oil by wool spinning and wool machine, and the wool is stuffy in the wool warehouse, and then pretreated by pre-opening equipment such as cotton opener. The air duct entering the gross silo is a 360 ° rotating air duct, and a spray is installed around the air duct to continuously spray the prepared crude oil or antistatic agent.
For raw materials that cannot be rolled, only the wool hopper can be used. For example, after the raw materials are loosened by the wool machine, they are directly fed into the carding machine by the wool hopper.
The hemp is humidified with special flax humidifier or emulsion, and the hemp is humidified layer by layer with high-pressure spray equipment for standby.
For protein composite fiber with smooth surface and poor cohesion, such as soybean protein composite fiber, mix 0.7%~1% of the dry weight of the raw material to be treated with antistatic agent and 10 times of water evenly, add antistatic agent during antistatic treatment, spray it on the loose raw material, stir evenly, soak it in the cotton storage room for 24 hours, and then dehumidify it in the open air for 3~5 hours, and put it into production after feeling good.
6.1.4 Determination of wettability and permeability of crude oil
Pull-off method in wool mill is one of the commonly used methods to measure the surface tension coefficient of various wool oil aqueous solutions at 0.1% concentration. The characteristic of this method is to measure the surface tension of liquid directly with a weighing instrument. The measuring method is intuitive and the concept is clear. Y151 fiber friction coefficient tester is selected to measure the dynamic and static friction coefficient of fiber with crude oil. According to the national standard GB/T14342-93 test method for specific resistance of synthetic staple fiber, YG321 is used to measure the effect of wool oil on the specific resistance of wool fiber and other fibers. Select conductivity instrument to test the conductivity of crude oil at different concentrations.
6.1.5 Other precautions in production
(1) In case of mass production, the wool bag (main length 34.04mm, fineness 5.2dtex) purchased by the wool processing plant is directly mixed with the cotton bag grab on the disc grabber for spinning, without any pretreatment. It not only meets the requirements of product quality, but also takes full consideration of cost saving to reduce the loss of wool fiber.
(2) In the process of cleaning, the cotton grabbing machine in the cotton mill itself has the function of mixing. If there is a partner with the wool machine, the multi-fiber mixing effect can be satisfied by "laying horizontally and taking directly".
(3) Cotton spinning carding machine is suitable for cotton type length fiber, such as cashmere, yak cashmere, lamb cashmere, etc. Pure wool and pure hemp shall pass the relevant equipment of wool pretreatment as far as possible.
(3) The cotton spinning drawing frame selects the drawing frame specially configured for spinning medium-long chemical fiber to prevent the ultra-long fiber in wool, silk and hemp from being broken. Due to the large spacing, the short fiber speed is controlled by the pressure bar. Of course, wool and other fibers have front and back hooks. The ability of drawing machine to eliminate hooks and sliver separation are not as good as those of carding machine, which needs to be compensated and adjusted in relevant processes.
(4) Cotton spinning equipment is used in most of the semi-worsted spinning projects. According to the needs of varieties, roving should be transformed into an electromechanical and computer-controlled four-roller double-loop drafting equipment. The spinning frame is a medium length spinning frame with elongated top pin, which is suitable for medium length fibers. It is better to improve the quality of semi-worsted yarn by siro spinning or compact spinning.
(5) The equipment such as rear parallel twisting adopts the new type of drum, parallel twisting and double twisting equipment with high degree of automation and less joints and defects.
7、 Conclusion
In order to solve the technical shortcomings of cotton spinning equipment in spinning non-cotton, especially wool, hemp, spun silk and other raw materials with poor spinnability, it is necessary to comprehensively and systematically transform, graft and innovate the single function of the existing cotton spinning equipment. In particular, the cotton spinning pre-spinning process should learn from the semi-worsted pretreatment technology, including technology, equipment, equipment, improvement of spinnability, elimination of static electricity, crude oil, additives, anti-skid agent and other technologies and use methods. Meet the requirements of quality, output, efficiency, cost performance, etc
souce:https://mp.weixin.qq.com/s/H6LMvQHKj5oJPC-xSptE4A
